27 July 2010

Open And Disassemble Western Digital My Book World

Here is a tutorial on how to open a Western Digital My Book World 2ND Edition (White Light), although I expect that it applies to most of the same edition Western Digital My Book range.

Of course you use the information here at your own risk.

See also this tutorial, which helped me open mine, I have tried to include a few more details in my explanation.

Here are roughly where all of the catches that keep the case locked are (they are duplicated on both sides of the case).


I found it easiest to remove the two end clips first. If you look through the holes in the case you can see the two clips (sorry my camera doesn't perform well under these conditions - no manual focus).


I used a plastic card (credit card) inserted at the corners of the case and then slid into position. Then pry the clips apart (looking through the end so you can see the clips). Pop all 4 (2 on each side).


The top and bottom have sliding rails, but they also have little tabs to ensure they don't just slide off.


I found it easiest to pop the rails off the tracks again sliding the plastic card in from the corner and then prying them slightly apart and then out to the side (not over to the end).


There are then two locking tabs under the front feet, you can depress them with a short thin poker. Be careful not to push to hard as they are made from reasonably brittle plastic.


There are also two tabs at the top visible from the outside, by this stage the case should be really loose and so they didn't present much of a problem, but you may need to be aware of them in case the keep it locked up.

You should now be able to slide the outer casing away from the inner.


I have photos of the inside disassembly, although it is much more straight forward (no sneaky hidden clips and catches). I'll put them up if there is enough demand.

Briefly:
• Mine had a light pipe, remove this first, it should just slide out.
• Then remove the hard drive and electronics from the caddy (it is just sitting in there, not screws or locking bits). Pop it up at the front (light side) and then slide it forward and out.
• Remove the electronics by removing the 3 screws and slide the tray to release, this disconnects the hard drive from the extra electronics.

17 comments:

  1. Thanks A LOT man, saved me from going completely gray haired..!

    ReplyDelete
  2. Thanks a lot

    ReplyDelete
  3. if i do this without breaking anything i will lost warranty?

    ReplyDelete
  4. Thank you great post, photos and clear instructions.

    Would be good if you could include photos of the inside of the unit.

    ReplyDelete
  5. My rails got stuck but got it out !

    ReplyDelete
  6. Thanks a lot for this clear instructions ! I succeeded with a minimum of clip broken

    ReplyDelete
  7. Very cool, saved me time and effort using a credit card. My model didn't have locking or sliding clips, just needed to get the card in at the corners and rotate the card into a position to push in the clips. Two clips roughly located middle in the long part and a longer single clip both sides of the case top and bottom. Cover then slides right off as described. Nice one!

    ReplyDelete
  8. Nice looking tutorial! wish i had looked at this one Before i took my mybook apart.

    ReplyDelete
  9. This looks great. Mine is pretty spooked (sporadic connection) so I'm hoping pulling it and doing a direct connection will let me save some data.

    ReplyDelete
    Replies
    1. Did this work for you? Were you successful saving data? Mine is 'spooky' now and I'm hoping the same thing.

      Delete
  10. anyone know if you can upgrade the drive to a 3TB drive?

    ReplyDelete
  11. Broke only 1 of the clips. Nice instructions, thanks a lot! I took the uni apart to insert some green coloured plastic between the prism and the front casing. This thing is so damn bright, you can not watch a movie! But now it actually looks better, like some green fluid inside, reminds me of cateye of old radios.

    Cheers!

    ReplyDelete
  12. would really like photos of the inside disassembly!

    ReplyDelete
  13. Thank you! Gave me the confidence to apply leverage and yankage...

    ReplyDelete
  14. I just ripped the shit out of mine. This old technology just isnt worth saving.

    ReplyDelete
  15. Your best wager for roulette in Las Vegas is to play on a single-zero wheel rather than a double-zero wheel, as a result of|as a result of} the home edge 솔카지노 is reduce almost in half. A simple Roulette technique is to position a wager on purple or black. Double up in your wager each time you lose till you get your a reimbursement. Players can play at their very own tempo since betting time is unlimited. The player is at all times in control and clicks on the ‘PLAY NOW’ button every time they are prepared. The wheel closest to the following drop of the ball is then mechanically selected because the wheel on which the player is betting for this sport round.

    ReplyDelete